SSD cooler designed to keep NVMe temperatures under control during heavy loads, the Thermalright HR10 SSD Cooler promises steadier performance. Peace of mind for system builders and content creators who need sustained speed without thermal throttling. Is that a sensible upgrade for a high-performance PC?
⚡ At a Glance
- • Cooling Performance: Lowers NVMe temperatures by 10–30°C under load, reducing thermal throttling
- • Best for: PC builders and enthusiasts running sustained NVMe workloads and heavy transfers
- • Not ideal for: Systems without a free 4-pin PWM header or extremely tight drive bay clearances
AGHP technology uses four 5mm heatpipes plus double-sided thermal pads for efficient heat transfer. A compact PWM fan and stainless steel lower cover support PCI‑E 5.0 2280 SSDs while adding mechanical rigidity.
Sustained transfer speeds – Thanks to AGHP 4×5mm heatpipes
AGHP technology configures four 5mm heatpipes and uses full plating reflow to improve single-heatpipe conduction and counter gravity-related performance loss. Heat moves from the SSD to the aluminium fins more efficiently, spreading thermal load across the cooler.
Reduced thermal throttling keeps large file transfers and sustained reads/writes closer to peak speed. Consistent performance benefits heavy workloads like video editing and large archives.
Even cooling both sides – With double-sided 14.8 W/mK thermal pads and stainless steel lower cover
High-conductivity pads sit on the top and bottom faces of the 2280 SSD, while a stainless steel laminated lower cover increases the effective cooling area. That arrangement extracts heat from both PCB surfaces rather than relying on a single contact point.
Hotspots diminish across the drive, lowering temperatures across components. Added mechanical support helps prevent NVMe bending when mounting, improving long-term board stability.
Fast, unobtrusive active cooling – Thanks to the customised 30×30×10mm PWM fan
A compact PWM fan runs between 3500–6500 RPM ±10% with a 4-pin PWM interface and a 50cm cable for plug-and-play connection. Rated at DC 12V and 0.05 A, the fan ramps speed based on thermal demand.
Rapid airflow evacuates heat when drives ramp up, yet user feedback confirms the fan remains almost silent even at higher RPM. Simple motherboard connection makes installation straightforward in most builds.
✨ The 4 Key Reasons for Thermalright HR10 SSD Cooler
- AGHP 4×5mm heatpipes – Speeds heat transfer, reducing peak NVMe temperatures under sustained load
- Double-sided 14.8 W/mK thermal pads – Pulls heat from both PCB faces, preventing hot spots
- 30×30×10mm PWM fan (3500–6500RPM) – Rapid airflow removes heat fast while staying nearly silent
- Stainless steel laminated lower cover – Adds rigid mounting, stops NVMe bending under pressure
📋 Technical Details at a Glance
- Category: SSD cooler
- Compatibility: 2280 NVMe SSDs
- Supported interface: PCI‑E, supports PCI‑E 5.0 SSDs
- Cooling size: 90.3mm × 23.7mm × 43.8mm
- Material: Stainless steel lower cover and aluminium fins
❓ Frequently Asked Questions
Q: Will the cooler fit a standard 2280 NVMe drive?
A: Yes, designed specifically for 2280 form factor with stated cooling dimensions of 90.3mm × 23.7mm × 43.8mm.
Q: Does the fan need a motherboard header, and how is it powered?
A: The fan uses a 4-pin PWM interface and comes with a 50cm cable for plug-and-play connection to a DC 12V PWM header; rated current is 0.05 A.
Q: How much temperature drop can be expected under load?
A: Manufacturer guidance indicates a cooling effect of around 10°C–30°C depending on environment, and user reports confirm noticeably lower NVMe temperatures under heavy load.
🏆 Our Verdict
Ideal for builders and enthusiasts who push NVMe drives hard and need reliable sustained throughput. Combination of AGHP heatpipes, double-sided high‑conductivity pads and a high-speed PWM fan delivers active, wide-area cooling plus mechanical support. While more capable than basic passive heatsinks, robust construction and PCI‑E 5.0 readiness make it a sensible long-term upgrade.
