Kitchen and basin tap connectors, XIFIRY Kitchen Monobloc Mixer Tap Connectors, deliver flexible, reliable supply lines. Users get peace of mind during installation and face fewer call-backs, whether a landlord or DIYer. Are M10 tails and a 400 mm length right for your tap setup?
⚡ At a Glance
- • Durability: EPDM inner hose combined with a grade 304 braided stainless steel exterior reduces kinking and resists wear
- • Best for: DIYers and plumbers installing standard kitchen or basin monobloc taps
- • Not ideal for: Taps that require M8 tailpieces or unusual, low-profile connections
Braided stainless steel flexible tails use an EPDM inner hose and grade 304 exterior for resilience. Listed as M10 rear end with a 1/2 BSP thread and supplied at 400 mm length.
Leak-free connections – with rubber sealing washers and solid brass connectors
Two nuts fitted with rubber sealing washers form the mechanical seal at connection points, while solid brass connectors create a corrosion-resistant joint. The sealed design is intended to reduce drips at both the tap and supply stop ends.
Reliable seals minimise the chance of leaks straight after fitting, cutting the need for early re-tightening or replacements. Ideal for installations where a dependable, leak-free finish matters.
Kink-resistant routing – thanks to EPDM inner hose and 304 stainless braid
An EPDM inner core provides flexibility and resistance to internal wear, while the grade 304 braided stainless steel exterior stops pinching and kinking when bending under sinks. The braid also helps protect the hose from abrasion.
Flexible routing under kitchen units becomes easier and safer, reducing the risk of burst hoses. Long-term durability is improved compared with non-braided or lower-grade options.
Straightforward fitment – with standard M10 rear end and 1/2 BSP thread, 400 mm length
One end uses a 10 mm rear tail listed as M10, and the opposite end is a 1/2 BSP threaded connection, matching common UK tap fittings. A 400 mm overall length gives reach for most sink installations.
Compatibility with standard tap sizes makes replacements quick and predictable, so fewer additional adapters are required. The length suits typical under-sink distances without needing extensions.
✨ The 4 Key Reasons for XIFIRY Kitchen Monobloc Mixer Tap Connectors
- Pre-fitted rubber washers – Prevents leaks immediately on installation, no extra parts needed
- 400mm length – Reaches most under-sink connections without awkward extensions or pipe bending
- Solid brass connectors – Heavy-duty joints resist corrosion for longer service life
- M10 / 1/2 BSP listing – Clear sizing reduces wrong purchases and installation delays
📋 Technical Details at a Glance
- Pack size: Pack of 2
- Inner hose material: EPDM
- Outer braid: Grade 304 braided stainless steel
- Connector material: Solid brass
- Thread sizes: 10 mm rear tail (M10) and 1/2 BSP thread
❓ Frequently Asked Questions
Q: Are these connectors compatible with most kitchen and basin taps?
A: Yes. The rear tail is listed as M10 (10 mm) and the opposite end uses a 1/2 BSP thread, matching standard UK monobloc tap fittings. Measure the outer diameter of the male thread with a caliper to confirm before purchase.
Q: Will they prevent water leakage after installation?
A: Sealing rubber washers and solid brass connectors provide a secure seal, and user feedback highlights reliable, leak-free performance when fitted correctly.
Q: Are they easy to fit for a DIY installation?
A: Yes, two nuts with rubber washers are supplied with each hose, and reviewers report straightforward fitting when replacing or installing new taps.
🏆 Our Verdict
Homeowners, landlords and plumbers fitting standard kitchen or basin monobloc taps will find these flexible tails well suited to everyday installations. Robust materials, solid brass connectors and included sealing washers combine to deliver dependable, long-lasting connections. While choices vary, the build quality and ready-to-fit kit represent good long-term value for routine plumbing work.
